When a dimension includes a fraction, the fraction is approximately 1 / 4″ in height, making the fractional numbers slightly smaller to allow for space above and below the fractional line.Īgain, it is particularly important that the numbers and fractions you may put on a sketch or drawing be legible. Numerals used to dimension an object are normally about 1/8” in height. To make your drawing look clean, use the same style throughout your drawing or sketch. Usually they have a slight barb, much like a fishhook. Correctly made, arrows are about 1/8” to 3/16” in length, and are about three times as long as they are wide. When dimensions will not fit in a space in the usual way, other methods are used to dimension clearly, when those crowded conditions exist.Īrrowheads are placed at each end of dimension lines, on leader lines, etc. The unidirectional system is usually best, because it is more easily read by workmen. They may be placed so they read from the bottom of the sketch (unidirectional dimensions) or from the bottom and right side (aligned dimensions). There are two basic methods of placing dimensions on a sketch. Otherwise, costly time and material will be wasted. Remember, the person reading your drawing needs to clearly understand, beyond question, how to proceed. Use common sense keep dimensions as clear and simple as possible. Avoid dimensioning to a hidden line and avoid the duplication of dimensions. It is important to remember to place dimensions on the views, in a two or three view drawing, where they will be the most easily understood. Sometimes, however, it is necessary to dimension on the object. Notice in this example the larger dimensions are correctly placed outside, or beyond the shorter dimensions, and that the dimensions are preferably not drawn on the object itself. Also, there should be not gaps where extension lines cross. There should be a gap of about 1 / 16″ where the extension line would meet the outline of the object, and the extension line should go beyond the outermost arrowhead approximately 1 /8″. Usually, the dimension line meets the extension line at right angles. Extension LinesĮxtension lines on a drawing are fine, dark, solid lines that extend outward from a point on a drawing to which a dimension refers. Either 4’-5” or 53”, they both mean the same thing but if there is a mix of dimensioning it can become easy to look at 4’-8” and see 48”. When calling out dimensions that are over 12”, make sure ALL of dimensions are called out in total inches or feet inches throughout the entire drawing. Be sure that it is clear how dimensions are called out. Dimensions over six feet are usually shown in feet and inches. Note: Dimensions less than six feet (72 in.) are given in inches. Here is how dimension lines should be sketched: The most important thing is that the drawing needs to be “clean” and dimensions need to be located in a space where they cannot be confused with a surface they are not intended to be used for. You do not necessarily have to remember this, but you should remember not to crowd your dimension lines and to keep them a uniform distance apart. The other dimensions beyond the first dimension (if any) should be approximately 3/8″ apart. In either case, the dimension line which is closest to the object should be placed approximatelyġ/2″ away. In architectural and structural sketches and drawings, the numerals are usually above an unbroken dimension line. In machine sketches and drawings, in which fractions and decimals are used for dimensions, the dimension line is usually broken near the middle to provide open space for the dimension numerals. It indicates direction and extent of a dimension. The dimension line is a fine, dark, solid line with arrowheads on each end. The United States standardized 1/8” vertical numbers are correctly formed as follows: The number forms presented here have been determined to be the most legible, and are used by industry nationwide. Therefore, the study of numbers forms is justified. The reason for such review is simply that incorrectly or carelessly made numbers on a drawing or sketch can easily be misinterpreted by someone on the job. It may seem a bit basic, but a few exercises with the shapes of numbers comes before dimensioning. In that way you will understand not only how to interpret a drawing to get the information you need, but also how to dimension your sketches so that they can be used to communicate size information to others. Therefore, your next step is to learn the basics of dimensioning. It tells this with views, which describe the shape of the object, and with dimensions and notes, which gives sizes and other information needed to make the object. If a drawing is to be complete, so that the object represented by the drawing can be made as intended by the designer, it must tell two complete stories.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |